A Guide to Resetting Your Holosun EPS Carry Red Dot

Wiki Article

Resetting your Holosun EPS Carry red dot sight to its original state can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. Start by locating the reset button on the back of the sight. This small lever is often unmarked but can be easily identified by its location.

• Beginning a factory reset, you'll need to hold down the reset button for a specific duration of approximately 5 seconds. You should see a changing illumination pattern on the sight indicating that the reset process is active.
• Once the process is complete, the indicator will return to its normal state.
• The red dot sight is now reset to factory defaults. You can then proceed with configuring it according to your preferences.

Be sure to always refer to the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.

Resetting Your Holosun EPS Carry to Factory Settings

Need to Adjust your Holosun EPS Carry Sight back to its Starting configuration? It's Simple. Here's how:

First, ensure the Red Dot is On. Then, locate the Control labeled "Mode".

Press and hold this Button for approximately 5 seconds.

You should Detect a series of Changes on the Display. This indicates that the EPS Carry is now Back to Factory Settings to its Basic configuration.

Once complete, release the Switch. Your Holosun EPS Carry is now Ready with all settings at their Starting values.

Calibrating the Holosun EPS Carry Red Dot Sight

The Holosun EPS Carry Red dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic calibration. This can be easily accomplished by following these simple steps: First, find the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small wrench, carefully turn the screws to modify the point of impact. Start by making small adjustments and test fire the sight at various distances to ensure accuracy. Continue this process until you achieve a desired zeroing point.

• Remember that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
• Confirm that the battery is fresh and properly installed before making any adjustments.
• If you encounter difficulty zeroing your sight, consult the manufacturer's instructions for further assistance or contact Holosun customer support.

Reset Factory Settings for Holosun EPS Carry

To reset your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, activate the optic by engaging the switch located near the side of the unit. Next, utilize the adjustable buttons found on the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and choose it using the designated button. The here EPS Carry will then initiate a reset sequence, which may take a few moments. Once complete, your sight will be restored to its default configuration.

• Note: During the reset process, all user-configured settings will be erased.

Reset Your Holosun EPS Carry in a Flash

Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:

First, turn off your red dot. Then, find the tiny reset button on the side of the sight. Use a small implement like a paperclip or a pin to press and activate the reset button for about 5 seconds. You'll know it worked when the display starts flashing.

• Allow
the sight to cycle through its startup sequence. This might take a few moments.
• Your Holosun EPS Carry is now reset to factory default settings!

Reset a Holosun EPS Carry Red Dot

Need for the purpose of new configuration setup? Here's how to accomplish this to Factory Reset your Holosun EPS Carry Red Dot.

First, ensure the red dot is powered on. Next, locate the tiny button on the left/right side of the sight's housing/body. Maintain a continuous press on this button for at least 5 seconds/3 seconds. You should observe a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Let go the button and your Holosun EPS Carry Red Dot is now restored to factory settings.

Report this wiki page